(0,80mm) .0315" eedp series eedp?016?06.00?ra1?ra1?4 captive panel screw and latching options mates with vertical and right angle connectors on board 30 awg twinax ribbon cable eedp?016?08.00?ds1?ra2?1 100 differential pair routing www.samtec.com mates with: mec8-02-ra, hsec8 specifications for complete speci cations see www.samtec.com?eedp cable: 30 awg twinax micro ribbon signal routing: 100 differential cable bending radius: (11,11mm) 7/16" min current rating: 1 a max propagation delay: 4.67 nsec/meter operating temp range: -20? to +90? skew (pair-to-pair): <10 ps/ft skew (within a pair): <5 ps/ft emi performance: fcc class a pinout map: see web address above rohs compliant: ye s oal = wire length + (17,65) .695 (1,60) .062 wire length (1,27) .050 c b n 02 n-1 01 a #4-40 thread no. of pairs ??xx.xx? = wire length in inches (95,3mm) 03.75" minimum ?008, ?016, ?024, ?032 eedp wiring option end no. 2 end no. 1 end no. 1 (-ds1 standard shown) end no. 2 (-ra2 flipped shown) wire length ?1 = pin 1 to pin 1 ?2 = pin 1 to pin 2 ?3 = pin 1 to pin n-1 (?024 n/a) ?4 = pin 1 to pin n (?024 n/a) specify end option from chart application specific ?customized routings ? board hardware for mounting with right angle captive screws (rah-01) ?other terminations ?other lengths contact dr@samtec.com a no. of pairs ?008 ?016 ?024 ?032 (24,51) .965 (35,10) 1.382 (44,70) 1.760 (53,31) 2.099 (34,67) 1.365 (45,26) 1.782 (54,86) 2.160 (63,47) 2.499 c (26,00) 1.024 (35,99) 1.417 (45,01) 1.772 (54,00) 2.126 b connector cable eedp?8 eedp?6 eedp?4 eedp?2 hsec8/mec8?13 hsec8/mec8?25 hsec8/mec8?37 hsec8/mec8?49 assembly end option specify x=1 for standard orientation; x=2 for ipped orientation (xx1 to xx1 and xx2 to xx2 require -3 or -4 wiring) (xx1 to xx2 and xx2 to xx1 require -1 or -2 wiring) ?dvx ?dsx -rax ?rsx ?lvx ?rlx vertical vertical with screws right angle right angle with screws vertical with latches right angle with latches (6,76) .266 (17,99) .708 hsec8 to eedp?dvx mec8?ra to eedp?rax processing conditions will affect mated height. applications applications latching system option for rugged applications. note: cable lengths longer than 40.00" (1 meter) are not supported with s.i. test data. note: this series is non-standard, non-returnable. f-211 supplement high speed edge card cable assembly cable length rated @ 7db insertion loss 19.68" (0,5m) 7.25 ghz / 14.50 gbps 39.37" (1m) 3.42 ghz / 6.84 gbps performance and complete test data available at www.samtec.com?eedp or contact sig@samtec.com
|
